Concrete Cleaning, Polishing & Sealing Services Melbourne

Professional Concrete Cleaning, Polishing and Sealing in Melbourne

Total Cleaning Melbourne provides a cleaning, stripping, polishing and sealing service designed to bring existing concrete floors back to life. The process removes old coatings, lifts oil and stain contamination from the pores of the concrete, then applies a commercial-grade sealer in your choice of gloss, satin, or matte finish. The result protects the concrete against future staining and wear, and can be maintained for one to three years before a full re-strip and reseal is required.

Service scope: We service existing concrete floors. We do not offer diamond grinding, honing, or epoxy floor coating - those are specialist services performed by concrete grinding contractors. We also do not service newly-installed concrete or handle moisture testing on new slabs. Our focus is the refresh-and-restore cycle for concrete that is already in place and has served for some time.

As the Australian Building Codes Board notes, maintaining floor surfaces in commercial and residential buildings is essential for safety and longevity. Unsealed concrete absorbs oils, moisture, and staining agents over time, leading to permanent discolouration and surface degradation. Professional polishing and sealing creates a protective barrier that extends the floor’s lifespan and reduces ongoing maintenance costs. For properties that also need vinyl floor polishing or tile and grout cleaning, we can service multiple floor types in a single visit.

How Do We Restore Concrete Floors?

Our concrete restoration process begins with stripping the old polish or sealer to expose a clean surface. The floor is then professionally polished to your chosen finish — high-gloss, satin, or matte — and sealed with a commercial-grade protective coating. This protects the concrete from scratching, scuffing, and staining, and the result can be maintained for one to three years with periodic buffing depending on foot traffic and wear.

Total Cleaning Melbourne applies this method to both indoor and outdoor concrete surfaces across Melbourne, from residential garage floors to large-format commercial and industrial facilities. Our technicians are experienced with the specific challenges of Melbourne’s climate, where temperature variation causes concrete to expand and contract, making regular professional maintenance essential for long-term floor performance.

Why Choose Total Cleaning Melbourne for Concrete Polishing?

• Experienced technicians trained in concrete surface restoration and polished concrete maintenance
• Specialised equipment for strip, clean, polish and seal
• Glossy or matte finish options to suit your style
• Indoor and outdoor concrete applications
• Residential, commercial and industrial properties
• All Melbourne suburbs serviced

What Surfaces Do We Polish and Seal?

• Garage floors
• Polished home floors and open-plan living areas
• Factory and warehouse floors
• Display rooms and showrooms
• Cafes, restaurants and retail spaces
• Tile and grout surfaces in commercial kitchens, bathrooms, and entryways

How Does the Concrete Polishing Process Work?

1. Strip - existing polish or sealer is removed to expose a clean surface
2. Clean and prepare - surface imperfections and stains are treated and the floor is prepared for polishing
3. Polish - floors are re-polished to your chosen finish (glossy or matte)
4. Seal - a protective commercial sealer is applied to lock in the finish

The sealed finish can be maintained for 1-3 years with periodic buffing, depending on foot traffic and wear.

What Does Our Concrete Polishing Service Include?

Our concrete floor service covers the full restoration and protection process:

• Inspection and assessment of current floor condition
• Stripping of existing coatings, old sealers, and surface contamination
• Surface preparation to address imperfections, stains, and contamination
• Polishing to your chosen finish - high-gloss, satin, or matte
• Application of commercial-grade sealer for long-lasting protection
• Edge work and detail areas around walls, pillars, and floor penetrations
• Outdoor concrete cleaning and sealing for driveways, paths, and courtyards
• Degreasing treatment for oil-stained garage or workshop floors
• Periodic maintenance buffing (ongoing service)

Why Is Concrete Polishing Popular in Melbourne Homes and Businesses?

Polished and sealed concrete floors have become increasingly popular across Melbourne’s residential and commercial property market. In homes, polished concrete is favoured for its clean, modern aesthetic in open-plan living areas, kitchens, and entertaining spaces - particularly in new builds and architectural renovations across Melbourne’s inner suburbs such as Fitzroy, Richmond, Brunswick, and Collingwood, as well as in contemporary homes across the outer suburbs.

In commercial settings, sealed concrete is the floor of choice for cafes, restaurants, retail spaces, showrooms, warehouses, and industrial facilities across the greater Melbourne area. Its durability, ease of cleaning, and professional appearance make it highly practical for high-traffic environments. For properties with a mix of flooring types, we also offer professional vinyl floor buffing and polishing to maintain a consistent, well-presented finish throughout your premises.

Melbourne’s climate introduces specific challenges for concrete floors. The city’s variable temperatures cause concrete to expand and contract, and its porous nature means it readily absorbs oil, moisture, and staining agents if not properly sealed. Regular professional maintenance - including periodic buffing and re-sealing - protects your investment and dramatically reduces the ongoing maintenance burden. Our team services all Melbourne suburbs, Monday to Friday, including commercial sites requiring after-hours work.

Concrete Cleaning Melbourne

Before polishing or sealing, concrete has to be cleaned properly - otherwise contaminants trapped under the new coating lead to patchy bonding, premature coating failure, and ongoing staining showing through. Our concrete cleaning service in Melbourne covers:

• Embedded dirt and grime removal - built up over years from foot traffic, spills, and weather
• Oil and grease stains - particularly on garage floors, car park bays, and workshop concrete. Our degreasing process lifts oil from the concrete’s pores rather than just wiping the surface.
• Rust and mineral staining - from metal furniture, tools, or water damage
• Moss and algae - common on outdoor concrete exposed to shade and moisture
• Paint spills and drips - often from renovations or DIY projects
• Tyre rubber marks - from vehicles and mobility equipment

We use professional-grade cleaners selected for the concrete type (sealed, unsealed, exposed aggregate, stamped) and appropriate water pressure for outdoor surfaces. Indoor concrete is cleaned with controlled-moisture methods to avoid slab saturation. For indoor applications where we also handle other floor types in the same property, see our tile and grout cleaning and vinyl floor cleaning services.

Concrete Sealing Melbourne

Concrete sealing protects the floor against oil, moisture, stains, and coating wear. Sealed concrete is easier to clean, resists staining far better than bare concrete, and lasts longer before needing remediation. Our sealing service is available in three finish levels:

• Gloss - reflective, showroom feel. Popular for display rooms, retail, and feature residential floors where visual impact matters.
• Satin - mid-level sheen, practical and presentable. Popular for garage floors, commercial interiors, and high-traffic residential areas.
• Matte - low-sheen, understated. Popular for modern residential interiors, outdoor concrete where glare control is a concern, and industrial settings.

We apply sealer after thorough cleaning (or cleaning-and-stripping for floors with existing failed coatings). Sealing alone - without the clean-strip preparation - is generally not recommended because contaminants under the sealer will show through and shorten the coating life. If your floor is already very clean, we can shortcut the process, but cleaning prep is almost always part of a quality seal.

Sealer selection depends on the floor’s intended use:

• Penetrating sealers (silicate densifiers) - work below the surface, do not alter the look, good for industrial floors
• Topical sealers (acrylic, urethane) - sit on the surface, offer gloss/satin/matte finish control, more common for residential and retail

We discuss sealer options during the quote so the choice matches the use case.

Driveway and Garage Floor Cleaning and Sealing

Driveway cleaning and sealing is one of our most common outdoor concrete services across Melbourne. Oil leaks from parked cars, tyre marks, moss in shaded sections, and general weathering dull driveways and leave permanent staining if left untreated. A cleaned-and-sealed driveway repels future stains, is easier to maintain, and delays the cracking and coating failure caused by Melbourne’s expansion-contraction temperature cycle.

Garage floors have the same issues plus heavier oil contamination. Car maintenance, workshop activity, and parked vehicles leaving drips all add up to a garage floor that’s visibly aged within a few years of installation. Our combined cleaning-and-sealing service lifts the oil, strips the old coating (if any), and seals with a satin or gloss finish that is easy to clean with a mop or hose going forward.

Typical driveway and garage jobs cover single-car residential driveways, double garages, commercial car park bays, and workshop concrete floors. For larger outdoor concrete cleaning needs beyond sealing - such as paths, patios, and pool surrounds - see our high-pressure cleaning service.

Warehouse and Commercial Floor Cleaning and Sealing

Commercial and industrial concrete floors see heavy foot traffic, forklift wear, chemical spills, and daily cleaning that standard residential maintenance cannot match. Our commercial concrete service covers:

• Warehouses and industrial facilities - concrete floor cleaning and sealing sized to the volume
• Retail showrooms - where presentation matters
• Car parks and loading docks - high-traffic concrete exposed to oil, fuel, and weather
• Manufacturing floors - where chemical resistance and slip safety are priorities
• Commercial kitchens and back-of-house - where hygiene and moisture control are regulated

Scheduling: After-hours and weekend work is available where disruption to operations is a concern - same as all our services. Please request scheduling in advance so we can confirm crew availability and quote the applicable rate differences transparently before booking. For larger commercial cleaning programs covering more than just concrete, we offer commercial cleaning as a full-service option.

What We Don’t Do

To be clear on scope so there are no surprises on the day:

• Diamond grinding - grinding concrete down through progressive diamond grits to produce a mirror-polished finish on the concrete itself. This is a specialist service performed by concrete grinding contractors. We do not offer it.
• Honing - partial grinding to expose aggregate with a softer finish. Also a specialist service.
• Epoxy floor coating - a distinct product category with its own application process. We do not apply epoxy coatings.
• Moisture testing on new slabs - new concrete needs curing time and moisture testing before first seal. We do not perform this; it is handled by the concrete installer or a specialist testing contractor.
• New concrete installation - we do not pour or install concrete floors.
• Sanding of newly-installed concrete - the initial finish on a new slab is the installer’s responsibility.

Our focus is cleaning, stripping old coatings, polishing to a sealer-applied finish, and applying new sealer to existing concrete floors - the refresh-and-restore cycle.

Where Do We Offer Concrete Polishing in Melbourne?

We provide concrete polishing and sealing across the Melbourne metropolitan area, including Fitzroy, Richmond, Brunswick, Collingwood, Heidelberg, Ivanhoe, Bundoora, Mill Park, Epping, and Thomastown. We service both residential properties and commercial or industrial facilities.

Each technician on our roster holds IICRC certification, is fully insured, and has been police-checked.

Frequently Asked Questions

How long does a concrete polishing job take?

The time depends on the floor area, its current condition, and the number of stages required. A standard single-car garage floor typically takes one day. Larger commercial floors, floors requiring additional preparation to remove deep staining or damage, or projects with complex edge work may take longer. We provide an accurate timeframe with your quote after inspecting the floor.

How long does a sealed concrete floor last?

A professionally polished and sealed concrete floor can be maintained for one to three years before a full re-polish is required, depending on foot traffic, wear, and the type of sealer used. Periodic buffing between full services extends the life of the coating significantly. We recommend a maintenance buff every six to twelve months for commercial floors and annually for residential floors in living areas.

Can you remove oil stains from a garage concrete floor?

Yes. Oil stains on garage concrete are one of the most common requests we receive. Our process includes a professional degreasing treatment applied before polishing, which breaks down and lifts oil contamination from the concrete’s pores. In most cases, oil stains can be significantly reduced or eliminated. Very old, deeply penetrated oil staining may require additional treatment stages. Our technician will assess and advise at the time of inspection.

What is the difference between concrete polishing and concrete grinding?

Concrete grinding uses diamond-tipped abrasives to mechanically grind down the concrete surface through progressive grits, producing a mirror-gloss polished finish on the concrete itself. This is a specialist service performed by concrete grinding contractors - we do not offer it. Our concrete cleaning, polishing and sealing service uses chemical stripping, professional cleaning, and protective sealer in gloss, satin, or matte to refresh and protect existing concrete without removing surface material. It is the right choice when your concrete is sound but tired, stained, or dull and you want it cleaned, stripped of old coating, and resealed.

Can you clean and seal my driveway?

Yes. Driveway cleaning and sealing is a common outdoor concrete service. We clean off embedded dirt, moss, oil residue, and tyre marks, then apply a protective sealer matched to outdoor conditions. A sealed driveway repels stains better, is easier to maintain, and delays the dulling and cracking that comes from Melbourne’s variable climate. Existing concrete driveways only - we do not seal newly-poured driveways.

Do you seal concrete in gloss, satin or matte?

Yes - all three finish levels are available. Gloss gives a reflective, showroom feel suited to display rooms, retail, and feature residential floors. Satin is a practical mid-level sheen popular for garage floors and commercial settings. Matte is low-sheen and understated, popular for modern residential interiors and outdoor areas where glare is a concern. We discuss finish options during the quote so the result matches your expectations.

Do you work on new concrete or only existing floors?

Existing concrete floors only. New slabs require curing time (typically 28 days or more) and a specific first-seal process that is handled by the concrete installer or a moisture-testing specialist - not by a refresh-and-restore service. Once your concrete has been in service and needs cleaning, re-stripping, or re-sealing, we take over.

How Can You Get a Free Quote?

Contact Total Cleaning Melbourne for professional concrete floor polishing and sealing. We service all Melbourne suburbs, Monday to Friday.